top of page

Usage Guidelines

A Corène fingerboard is fitted much like an ebony one: same tools, same gestures, same care. A few points differ, because the material is perfectly homogeneous and completely non-porous. This guide walks you through them, from the first shaving to the final polish.
 

Working the fingerboard
The material is completely homogeneous: no grain direction, no hard or soft zones, no hidden cracks. It can be planed, scraped, sanded and machined with the usual woodworking tools of the violin maker.

  • Keep your plane well sharpened. The top and bottom surfaces cut easily, while the sides are slightly harder, especially on cello fingerboards.

  • With no grain to follow, the material can be planed in any direction without tear-out. For the easiest finish, however, plane lengthwise.

  • On Extra Light fingerboards, at least 2 mm of material remains under the glue channels. Light planing is possible, but rarely needed. If you expect to remove more material, choose a Final Standard or a Large Standard.
     

Which glue
⚠️ Corène fingerboards must always be glued with the natural, reversible bone glue supplied with them.
Traditional hide glue does not hold properly on this material: hide glue needs a porous surface to penetrate, and Corène is completely sealed. Bone glue is a natural glue that has been used for centuries in many crafts. It bonds strongly to non-porous surfaces, and it remains reversible, so the fingerboard can be removed cleanly whenever needed.
Additional bone glue is available in our shop.
 

How to glue

  1. Prepare the glue. Dissolve the glue granules in a little water.

  2. Heat in a water bath at 70 °C until you get a viscous mixture, with the consistency of hide glue.

  3. Apply an even layer, position the fingerboard and clamp it (see below).

  4. Clean off the squeeze-out with a damp cloth before it sets.

  5. ⚠️ Keep it under clamps for at least 24 hours. Because the material is non-porous, the glue needs much more time than on ebony to set. A shorter clamping time cannot guarantee an optimal bond.
     

Clamping
⚠️ The top surface of a Corène fingerboard is cambered, and this camber is machined precisely.

  • Use a separate caul for each clamp, never a single long caul for all clamps. This is essential: each caul then follows the camber locally, and the pressure is spread evenly along the whole fingerboard.

  • For a violin, the ideal set-up is three clamps, each with its own caul. For larger instruments, add clamps accordingly, always one caul per clamp.

  • Use cauls and a method that neither deform nor flatten the camber, for example cauls shaped to the camber, or soft pads.

  • Tighten progressively, without excessive force.

  • Once again, keep it under clamps for at least 24 hours. Because the material is non-porous, the glue needs much more time than on ebony to set. A shorter clamping time cannot guarantee an optimal bond.
     

Finishing
The fingerboard arrives polished to a satin, mirror-like finish. After fitting, a final polish is all it needs. If you wish, a tiny drop of oil will bring out the shine, but really very little: the material absorbs nothing, and needs no other care to keep its properties over time.
 

How to remove
A Corène fingerboard is removed with the same technique as an ebony fingerboard:

  1. Slide a thin blade between the fingerboard and the neck.

  2. Apply gentle but steady pressure while working the blade forward under the fingerboard.

The fingerboard comes off cleanly, without tearing the neck. It may leave a very fine black trace on the neck, which can be removed with a little water.

Re-gluing

Give the underside of the fingerboard a light pass with the plane, clean it, and it can be glued again.
 

Need help?
Every instrument and situation is different. If you have a question about fitting a Corène fingerboard, write to us: we answer in English, French, and German.

Néo-Ébène Sàrl
Rte de Pailly 10 /VD

1047 Oppens

Switzerland

  • Facebook - White Circle

Subscribe to Updates

©2026 Corène by Néo-Ébène Sàrl

bottom of page